XZ 见解

工业紧固知识·行业趋势·技术见解

Cross-Drilled Fasteners: Define the Hole on the Drawing

Facebook
X
LinkedIn
红迪网
WhatsApp
电子邮件

Table of Contents

“Bolt with a cross hole” describes a feature, not a complete manufactured part. A supplier still needs to know where the hole is, how it is oriented and which requirements govern its finished condition. Give the hole its own drawing references instead of relying on a photograph of an existing assembly.

Locate the hole from an unambiguous reference

Have the approved drawing identify the hole centre relative to a stated datum or end face. Show whether the location is measured from the physical end, a shoulder or another defined feature. When a fastener has chamfers, an irregular end or a separate point, an informal instruction such as “near the end” can be interpreted differently by the buyer and manufacturer.

Specify the hole diameter and tolerance through the responsible designer. Show whether the feature passes completely through the part and identify any required relationship to flats, a head, another hole or a slot. If angular orientation is important, provide a view or datum arrangement that makes the requirement inspectable. Do not ask the supplier to choose a position solely because it is convenient to machine.

Describe the complete ordered condition

List the material designation, product specification and required finish for the fastener as a whole. Ask how the approved hole and edge requirements will be achieved in the delivered condition. If processing sequence matters to the design or inspection, have it stated in the approved requirements rather than assumed during quotation.

  • Fastener drawing number, revision and base product definition.
  • Hole diameter, tolerance and location reference.
  • Required orientation and relationship to other features.
  • Edge, burr and surface requirements from the drawing.
  • Material, heat-treatment and surface-finish requirements.
  • Inspection characteristics and required report references.

Keep manufacture separate from engineering approval

Drilling removes material from the fastener. The responsible engineer must approve the feature and its application; a machining quotation does not establish that the modified component retains the performance of an unmodified standard part. Do not describe a cross-drilled version as interchangeable merely because its main diameter and overall length match a catalogue item.

If the hole is intended to work with a retaining or locking component, identify that component and the approved assembly requirements. The supplier can review the drawing for manufacture, while engineering defines the acceptable joint and the installation procedure. Avoid adding a generic tightening instruction or drilling a finished installed fastener without the required engineering review.

Agree the inspection evidence before production

Assign a characteristic reference to each required hole measurement and edge check. Have quality staff agree the method, inspection coverage and acceptance criteria. For a first supply, request an agreed dimensional report connected to the drawing revision and sample identity. Photographs may help show the feature but do not establish a controlled measurement by themselves.

At receiving, connect the part markings or package lot references to the inspection file. If a hole is missing, misplaced or different from the approved revision, record the affected quantity and preserve the evidence. Route rework or concession proposals through the buyer's authorised process instead of accepting an undocumented workshop alteration.

Send the approved requirements for review

Send the drawing or full specification, quantity and destination to XZ Fastener for a manufacturing and quotation review. Include material inspection reports, dimensional reports and batch traceability in the requested document scope. Any EN 10204 3.1/3.2 or third-party inspection requirements need their issuing arrangements, scope and buyer approval confirmed before ordering.

For the wider purchase file, use our project fastener order control records. The stud length guide addresses overall and effective thread length separately.

搜索文章
订阅技术新闻

工业紧固知识·行业趋势·技术见解

快速联系业务专家

XZ 销售工程师

Bulk fastener quotations · MOQ 1,000 pieces

Tell us your fastener requirements. Our sales team will prepare your quotation.

Lead time: 3 days. Custom packaging available. Shipping time and order details are confirmed in your quotation.

Optional: attach drawings, photos or a specification list. Accepted: PDF, JPG, PNG, Word, Excel, XML and TXT.

感谢您的光临!

请将您的询问分享至 sales@xzfastener.com