Fabricant d'écrous hexagonaux zingués DIN 934
XZ Fastener supplies DIN 934 zinc plated hex nuts for machinery assembly, steel brackets, equipment maintenance, threaded rods, anchors, and bolt-nut-washer sets. Zinc plating is commonly selected for carbon steel metric hex nuts when buyers need clean appearance, basic corrosion protection, and practical cost control for indoor or light-duty environments. DIN 934 nuts can be matched with metric hex head bolts, DIN 933 full thread hex bolts, DIN 931 partial thread bolts, flat washers, and spring washers according to order requirement.
Spécifications rapides
What Buyers Should Know Before Sourcing DIN 934 Zinc Plated Hex Nuts
DIN 934 zinc plated hex nuts are commonly ordered with carbon steel bolts and washers, but thread pitch, nut grade, coating thickness, and mating bolt grade still need to be confirmed. Zinc plating gives a smoother appearance than hot dip galvanizing, but it is normally used for indoor equipment, general machinery, and moderate storage conditions rather than highly corrosive outdoor exposure.
Ajustement du filetage
Internal thread quality is critical for nut assembly. Buyers should confirm metric coarse or fine pitch and request thread gauge inspection when nuts are matched with coated bolts, threaded rods, or studs.
Matched Bolt Grade
DIN 934 zinc plated nuts are often matched with Grade 8.8 carbon steel hex bolts. For higher strength assemblies, nut grade should be checked with bolt grade, washer type, and tightening method before production.
Pour une référence produit proche, voir XZ Fastener’s Écrous hexagonaux métriques en acier au carbone zingué DIN 934 page for industrial fastening and equipment assembly.
Descriptions d'achat courantes
Buyers may describe DIN 934 zinc plated hex nuts in different ways. A practical purchasing description should include standard, size, thread pitch, grade, material, finish color, quantity, and packaging method.
- DIN 934 zinc plated hex nuts, M10, carbon steel, Class 8
- DIN 934 metric hex nuts, M12, white zinc plated, bulk carton packing
- Carbon steel zinc plated DIN 934 nuts with Grade 8.8 carbon steel hex bolts
- DIN 934 zinc plated nuts matched with zinc plated DIN 933 bolts and flat washers
- DIN 934 hex nuts, yellow zinc finish, small box packing for distributor stock
- Metric zinc plated nuts for threaded rods, anchors, and equipment maintenance
For complete assemblies, XZ Fastener can help match nuts with tailles de boulons et de rondelles, including DIN 933 full thread hex bolts, DIN 931 partial thread bolts, flat washers, and spring washers.
Tableau des spécifications détaillées
| Article | Exigence typique | Notes de l'acheteur |
|---|---|---|
| Norme | DIN 934 écrous hexagonaux métriques | Confirmez si le projet nécessite des dimensions DIN, ISO, ASTM ou le dessin de l'acheteur. |
| Taille du fil | M2 to M64 common range; other sizes reviewed by inquiry | Provide exact size and pitch, especially for fine-thread nuts. |
| Type de filetage | Filetage métrique grossier en fourniture courante ; emplacement fin disponible sur demande | Thread gauge inspection can be arranged according to order requirement. |
| Catégorie de noix | Class 4, 5, 6, 8, 10 or buyer-specified grade | Class 8 is commonly matched with Grade 8.8 bolts. |
| Matériel | Carbon steel as common supply for zinc plated DIN 934 nuts | Stainless steel should normally use plain or passivated finish rather than zinc plating. |
| Terminer | White zinc, blue-white zinc, yellow zinc, black zinc; trivalent chromium available upon request | State color and environmental requirements before production. |
| Boulons assortis | DIN 931, DIN 933, ISO 4014, ISO 4017, tiges filetées, goujons | For full-thread assemblies, buyers may pair nuts with boulons DIN 933 zingués. |
| Rondelles assorties | Rondelles plates, rondelles élastiques, rondelles trempées | Washer size and hardness should match bolt grade and clamped material. |
| Contrôle | Dimensions, thread gauge, hardness, proof load, plating appearance, coating thickness | Inspection scope should be agreed before production and packing. |
| Emballage | Carton en vrac, petite boîte, sac, palette, marque privée, étiquette code-barres | L'emballage du distributeur et les étiquettes de projet peuvent être préparés selon les exigences de la commande. |
Pour plus de détails sur les appels d'offres spécifiques aux écrous, consultez le guide XZ Fastener’s sur exigences en matière de filetage d'écrou, de qualité, de norme et de revêtement.
Explication du matériau et de la qualité
Most DIN 934 zinc plated hex nuts are made from carbon steel because the zinc layer provides basic corrosion protection while the steel body provides mechanical strength. Class 8 DIN 934 nuts are commonly used with Grade 8.8 carbon steel hex bolts. Lower classes may be suitable for general equipment, while higher classes should be reviewed with bolt grade, proof load, and tightening method.
The nut should not be selected only by thread size. Buyers should confirm grade, bolt compatibility, washer selection, zinc plating color, and whether proof load or hardness reports are required. For high-strength bolted joints, the nut must support the intended clamp load without thread stripping or grade mismatch.
Guide de sélection de finition de surface
Zinc plating is often chosen for DIN 934 nuts when buyers need a clean metallic appearance and practical corrosion protection for indoor or sheltered applications. It is thinner and smoother than hot dip galvanizing, but it should not be used as a direct replacement for heavy outdoor corrosion protection without checking service conditions.
| Terminer | Utilisation appropriée | Considération d'achat |
|---|---|---|
| White zinc / blue-white zinc | Machinerie générale, assemblage d'équipements, stock intérieur | Common appearance for zinc plated DIN 934 nuts and compatible bolts. |
| Zinc jaune | Distributor stock, color-coded maintenance kits, general hardware | Confirmer la tolérance d'apparence et les exigences environnementales locales. |
| Zinc noir | Black appearance requirements with better appearance control than black oxide in some assemblies | Check corrosion target and color consistency before bulk production. |
| Oxyde noir | Machinery interiors and oiled assemblies | Lower corrosion protection than zinc plating unless oil or added protection is applied; can be matched with black oxide DIN 933 bolts. |
| Galvanisé à chaud | Outdoor structures, guardrails, brackets, exposed construction hardware | Thicker zinc layer requires internal thread-fit control; often matched with hot dip galvanized DIN 933 bolts. |
| Dacromet ou Géomet | Équipements extérieurs et ensembles sensibles à la corrosion | Utile lorsque les performances contre la corrosion et l’accumulation contrôlée du revêtement sont toutes deux importantes. |
Pour une comparaison des revêtements, consultez le guide de revêtement des fixations et le guide axé sur l'assemblage sur sélection de l'état de surface des écrous, rondelles et boulons.
Fabrication et contrôle qualité
DIN 934 zinc plated hex nuts are generally produced through wire or bar preparation, cold forming or hot forging depending on size, tapping, heat treatment when required, zinc plating, inspection, and packing. Internal thread quality and plating consistency are especially important because the nut must assemble smoothly with metric hex head bolts, threaded rods, and studs.
- Contrôles de la largeur des surplats, de la hauteur de l'écrou, du chanfrein et du filetage interne
- Go/no-go thread gauge inspection for metric thread compatibility
- Hardness and proof load testing when required by grade or project specification
- Zinc plating color, coverage, adhesion, thickness, and internal thread build-up review
- Séparation des tailles, poids du carton, étiquette, marque de palette et contrôles d'identification des lots
For thread-fit control between nuts and bolts, buyers can review XZ Fastener’s guide on inspecting thread fit between bolts and nuts.
Applications
Machines et équipements
Zinc plated DIN 934 nuts are used with metric hex head bolts in machinery frames, equipment bases, conveyors, industrial skids, and general maintenance assemblies.
Matériel de construction
Carbon steel zinc plated nuts can be supplied for brackets, plates, light structural hardware, and indoor construction assemblies where basic corrosion protection is required.
Assemblages de tiges filetées et de goujons
DIN 934 zinc plated nuts are commonly used with threaded rods, double-end studs, anchor systems, and adjustable assemblies where smooth thread fit matters.
Programmes de stocks de distributeurs
Les importateurs et les grossistes peuvent demander des tailles variées, des étiquettes de carton, des étiquettes de codes-barres, des marques de palettes et des ensembles boulons-écrous-rondelles assortis en fonction des besoins de l'entrepôt.
Comment obtenir un devis plus rapide
A complete inquiry helps XZ Fastener check material, tooling, grade, zinc plating color, packing, and lead time more efficiently. If the nuts will be matched with bolts, include the bolt standard and grade in the same request.
- Norme : DIN 934 ou référence du dessin de l'acheteur
- Liste des tailles : taille et pas de filetage, tels que M8, M12, M16 x 1.5.
- Nut grade: Class 4, 5, 6, 8, 10, or project-specified grade
- Material: carbon steel as common supply for zinc plated nuts
- Finish: white zinc, blue-white zinc, yellow zinc, black zinc, or other plating requirement
- Quantité : quantité par taille et demande répétée attendue si disponible
- Emballage : carton en vrac, petite boîte, sac, palette, marque privée, code-barres ou marque de projet
- Inspection requirements: dimensional report, thread gauge, hardness, proof load, plating thickness, salt spray, or third-party inspection
Envoyez vos coordonnées via le demander un devis page ou contacter XZ Fastener for review of DIN 934 zinc plated hex nuts and matched fastener assemblies.
FAQ
What are DIN 934 zinc plated hex nuts used for?
They are used with metric bolts, threaded rods, studs, and washers in machinery, equipment, construction hardware, brackets, maintenance kits, and distributor stock programs.
Can zinc plated DIN 934 nuts be used with Grade 8.8 bolts?
Yes. Class 8 DIN 934 nuts are commonly matched with Grade 8.8 carbon steel hex bolts. The final selection should also consider washer type, tightening method, and assembly requirements.
What zinc plating colors are available?
Common options include white zinc, blue-white zinc, yellow zinc, and black zinc. Color, coating thickness, and salt spray requirement should be confirmed before production.
Are zinc plated nuts suitable for outdoor use?
Zinc plated nuts can be used in light or sheltered environments, but hot dip galvanized, Dacromet, Geomet, or stainless steel options may be better for severe outdoor exposure.
XZ Fastener peut-il fournir des écrous DIN 934 avec boulons et rondelles ?
Yes. DIN 934 zinc plated nuts can be supplied with DIN 931 bolts, DIN 933 full thread hex bolts, flat washers, spring washers, hardened washers, and assembled bolt-nut-washer sets according to order requirement.
Que dois-je fournir pour un devis précis ?
Please provide the size list, thread pitch, nut grade, material, zinc plating color, quantity, packaging method, inspection requirements, and any matching bolt or washer requirements.
Send Your DIN 934 Zinc Plated Hex Nut Inquiry
For a faster response, send your size list, finish, quantity, packaging method, and inspection requirements. XZ Fastener can review DIN 934 zinc plated hex nuts, matched washers, threaded rods, DIN 933 full thread hex bolts, Grade 8.8 carbon steel hex bolts, metric hex head bolts, zinc plated DIN 933 bolts, black oxide DIN 933 bolts, and hot dip galvanized DIN 933 bolts according to your purchasing plan.
Demander un devis
English 
Español 
Français 
Español de México 
العربية 
Deutsch 
Русский 
Tiếng Việt 
Bahasa Indonesia 
Italiano 
简体中文